Install Cloudbreak Deployer
Follow these steps to install Cloudbreak Deployer on your operating system.
The instructions below are for CentOS. If you are using a differnt OS, perform equivalent steps.
To run the Cloudbreak Deployer and install the Cloudbreak application, your system must meet the following requirements:
- RHEL / CentOS / Oracle Linux 7 (64-bit)
- Docker 1.9.1
- VM requirements:
- 8GB RAM
- 10GB disk
- 2 cores
You can install Cloudbreak on Mac OS X for evaluation purposes only. This operating system is not supported for a production deployment of Cloudbreak.
You must satisfy the following preprequisites before installing the Cloudbreak Deployer.
Make sure that the following ports are open:
- SSH (22)
- Cloudbreak (443)
Execute every command as root. In order to get root privileges execute:
Ensure that your system is up-to-date and reboot it if necessary (for example, if there was a kernel update):
yum -y update
Install iptables-services. Without iptables-services installed the 'iptables save' command will not be available:
yum -y install iptables-services net-tools
Then, configure permissive iptables on your machine:
iptables --flush INPUT && \ iptables --flush FORWARD && \ service iptables save
Configure a custom Docker repository for installing the correct version of Docker:
cat > /etc/yum.repos.d/docker.repo <<"EOF" [dockerrepo] name=Docker Repository baseurl=https://yum.dockerproject.org/repo/main/centos/7 enabled=1 gpgcheck=1 gpgkey=https://yum.dockerproject.org/gpg EOF
Next, install the Docker service:
yum install -y docker-engine-1.9.1 docker-engine-selinux-1.9.1 systemctl start docker systemctl enable docker
Cloudbreak Deployer Installation
Install Cloudbreak Deployer
Install the Cloudbreak Deployer and unzip the platform-specific single binary to your PATH. For example:
yum -y install unzip tar curl -Ls s3.amazonaws.com/public-repo-1.hortonworks.com/HDP/cloudbreak/cloudbreak-deployer_1.14.4_$(uname)_x86_64.tgz | sudo tar -xz -C /bin cbd cbd --version
Once the Cloudbreak Deployer is installed, you can set up the Cloudbreak application.
Initialize Your Profile
cbd by using:
mkdir cloudbreak-deployment cd cloudbreak-deployment
cbd by creating a
Profile file with the following content:
export UAA_DEFAULT_SECRET='[SECRET]' export UAA_DEFAULT_USER_PW='[PASSWORD]'
By default the
cbd tool tries to guess
PUBLIC_IP to bind Cloudbreak UI to it. But if
cbd cannot get the IP address during the initialization, set the appropriate value also in your
Generate Your Profile
Generate configurations by executing:
rm *.yml cbd generate
This creates the following configuration files:
- The docker-compose.yml file that describes the configurations of all the Docker containers required for the Cloudbreak deployment.
- The uaa.yml file that holds the configurations of the identity server used to authenticate users to Cloudbreak.
Start Cloudbreak Application
To start the Cloudbreak application, use the following command:
cbd pull cbd start
This will start all the Docker containers and initialize the Cloudbreak application. It will take a few minutes for all the services to start.
The first time you start the Coudbreak app, the process will take longer than usual due to the download of all the necessary docker images.
cbd start command finishes, use this command to check the logs of the Cloudbreak application:
cbd logs cloudbreak
You should see a message like this in the log:
Started CloudbreakApplication in 36.823 seconds. Cloudbreak normally takes less than a minute to start.
If you face permission or connection issues, disable SELinux:
- Set the
- Reboot the machine.
- Ensure the SELinux is not turned on afterwards:
setenforce 0 && sed -i 's/SELINUX=enforcing/SELINUX=disabled/g' /etc/ selinux/config
After you have installed Cloudbreak Deployer, perform cloud provider specific configurations and then provision a cluster. See cloud provider specific steps:
Edit on GitHub
Note: AWS and OpenStack Setup sections contain provider-specific and other additional